Guide Information Blogs

Put the seat post and seat in the seat post receiver, and install the trunk rack then on the back of scooters. Sure pull the seat post clampTheir roller is loaded from the box. We recommend charger for 6-8 hours before its first use continue. We recommend also the elevation of your roller after every use and before saving.

On the dashboard, a master makes/kill switch located close to the ignition. This switch are allowed to operate on the scooter and while loading. This switch will cut all power to the motor.When first plugged in the charger has on two red lights is lit at the same time, indicating that the charging has started. As soon as the light on the charger turns green, can the charger to remove and close the safety Cap.The X 360 used a hub brake on the rear wheel of the scooter activated by a lever hand brake on the left side of the handlebar. Squeezing the hand brake lever with his left hand activates the rear brake. Make sure the THROTTLE grip let go to engage the brakes. get here

The electric motor adopted for this vehicle is 24V 100W great power and strong anti-overload dedicated performance, which can meet the needs of your daily transportation continuously current hub Dynamo for electric vehicle, with the strengths of small volume, light weight, only.

The battery for this vehicle the lead chemical lead-acid battery for the electric vehicle is selected while has the following strengths: no necessary repair, high capacity and service life.Drive controller is the most important centre of the propulsion system of the entire vehicle with the function under voltage protection of the battery, current folds back circuit and put on the brake makes to interrupt. get here

Use the enclosed bolts and nuts, fixing of the gas tank on the right side of the rear frame. Run the gas lines to the frame to the engine it gently stuffed under the rear fenders.The scooter comes with 2 seat posts. It is inserted into the underside of the seat and and secured by tightening the nuts. The second Seatpost is inserted into the opening on the back/engine framework. Drag down the post in place with the supplied Allen wrench

Pushing to secure the seat post clamp on the bottom post and insert the upper seat post and attached seat in the low post and place by tightening the clamp. You can easily adjust the height by loosening the clamp and move to the top or bottom of the seat, then pull the bracket.Attach part of engine and rear frame.Have a second person to keep engine/rear light out of the ground the framework, set the attached screw Thrum the holes on the side of the rear frame and into the pipe on the front frame. Tighten the nuts securely at each end. get here

The charger has in this product is the specially developed intelligence charger. At the time, there is no need to be guarded by a specialist. Everywhere, where 110 v-240 v AC, can be used easily. Charger this charger can prevent and maintain the battery in the best condition.During the loading process, put the plug of the charger into the connector of body and plug to the current source. The charger is three to six hours. At the time, the current drive automatically stops and prevents so the vehicle not started.Drive controller is the most important centre of the propulsion system of the entire vehicle with the function of protection of the battery voltage circuit fold back and put on the brakes to interrupt electricity.

The electric motor for this car 24V 250W is dedicated continuously current hub Dynamo for electric vehicle, with the strong performance, anti-overload, only accepted that that your daily transport requirements canDownload X-Treme scooter X-Treme X-250 manual get here

The X-Treme XG505 used an identical rim and tires mounted on the front and rear wheels, which means that the tires can be rotated. The wheels are actually two wheel halves (split RIM) screwed together, to it easier end replace the tyre end remove hose.The rear wheel is equipped with a special spacer, sprocket, to accommodate while the wheel has a holder for the disc brake.

When you are finished the XG505 you can horseback riding it register for compact storage and transport folds. Use the XG505 folds, are, on the one hand, on the Klapp he push handle down while gently on the handlebars. WATCH OUT, NOT TO THEIR HEAD WITH THE HANDLEBAR FOR REFERENCE. Press until you feel the mechanism lock in position down.Fuel is mixed with air in the carburetor. If the engine is run at the factory, the CARB is adjusted basically. A Fut of their modification from time to time, depending on the climate and altitude may be required. get here