Tuesday, May 22, 2012

Ink System Failure On HP C7280

A. - Press and hold the #*# key.
B. - Press the ### key and release both keys.
Display should say #Enter Special Key Combo#
C. - Press and release in sequence the #1#, #2# and #3# buttons.
Display should say #Support# and display the FW rev (something like R0631R)
1. Press and release the right arrow button until the display says #System Configuration Menu#.
2. Press and release the #OK# button.
3. Display should say #Hardware failure status#. If not there already, Arrow Key over to #Hardware failure status#,
4. Press and release the #OK# button.
5. Display should say #Hardware failure status: Clear. Press OK to clear#.
6. Press and release the #OK# Button. Message changes to #Hardware failure status Cleared. Press Cancel to continue#.
7. Press and release the #CANCEL# button as many times as necessary, so that, either the #Welcome to Photosmart Express# screen appears, or, the #Ink System Failure# screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
8. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
9. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
10. Turn the unit on. The printer may display message #USE POWER BUTTON TO SHUTDOWN THE PRINTER# followed by #PRESS OK TO CONTINUE#. Press OK.
11. If the printer has already initialized, then go to the next step. If not, the printer will start the #ONE TIME INK INITIALIZATION PROCESS#. Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.
Read More..

Xante Ilumina Codes Oki 9800

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or - button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or - button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again.|| freereset
Read More..

Oki c5450 and c9300 Drum, Toner, Fuser, Belt Reset

1) Power ON printer while holding both the 0, 1, 6, 7 buttons until “OKIUSER” message apear in LCD.
2) Press + or - button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or - button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again... =)

OKI C5450n

1) Power ON printer while holding both the + & - buttons until “OKIUSER” message apear in LCD.
2) Press + or - button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or - button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again... =)
Read More..